Drivers
 

Home

 

DriverSearch.com
search for drivers
List & backup your drivers free
Add this search box to your site

Click Here for Device Driver and System Development
Click Here for Device Driver and System Development

Computer Setup/VP and PC Diagnostics

Version 1.76 A
27 Aug 1998


For all products except the Deskpro EP, SB, and EN Series, Computer Setup and PC Diagnostics are both pre-installed on the Diagnostics Partition.

The diskettes in this SoftPaq can be used to update these utilities on the Diagnostics Partition or to restore them if the Diagnostics Partition has been destroyed. Both utilities can be run by pressing F10 during power-up or reboot when prompted in the lower right corner of the screen on some models or when the cursor jumps to the upper right corner of the screen on other models.

Or they can be run directly from these diskettes if your system fails to respond.

NOTE: For the Deskpro EP, SB, and EN Series, Computer Setup/VP and Personal Computer Diagnostics must be run from diskette.

Computer Setup/VP allows the user to configure security and power management settings as well as system resources (DMA, IRQ, I/O Ports, and Memory). It is specific to the Deskpro models listed below.

Personal Computer Diagnostics contains programs that can test and inspect the state of the computer and its devices. It is used with the Deskpro models listed below, as well as other Compaq Desktops and Portables.

Fixes

This version will support all the features supported by Setup 1.75


Corrects a condition in Setup_VP when the installation includes a Colorgraphic Evolution 4 video controller, which controls up to four monitors from a single controller.

After saving changes in Setup_VP, a Plug and Play alert message is displayed and no video is displayed from the operating system when the drivers are loaded on the second, third or fourth monitor.

Sopported Systems

Family Models
Deskpro EN Series 6266, 6300, 6300A, 6300C, 6333, 6333C, 6350, 6400, 6400C, 6450, 6450+, 6500, P550, P600, P650, P700
Deskpro EN Series SFF 6300, 6300A, 6300C, 6333, 6333C, 6350, 6400, 6450, 6450+, 6500, Net PC 6300, Net PC 6400, P650, P700
Deskpro EP Series 6266, 6266C, 6300, 6300A, 6333, 6333C, 6350, 6400, 6400C, 6450, 6450+, 6500, P550, P600, P650, P700
Deskpro SB Series 6266, 6300, 6333, 6350, 6400
Prosignia 310 6300A, 6333, 6366C, 6400C
Prosignia 330 6350, 6400, 6450, 6450+, 6500, 6550, 6600, 6650, 6700, 6750
Prosignia 340 6466C, 6533C, 6550, 6600
Deskpro 6000 5166, 5200, 6180, 6200, 6233MMX, 6233X, 6266MMX, 6266X, 6300MMX, 6333
Deskpro 4000N 5166MMX, 5200MMX, 5233MMX
Deskpro 4000S 5166MMX, 5200MMX, 5233MMX
Deskpro 4000 5100, 5120, 5133, 5166, 5166MMX, 5166X, 5200, 5200MMX, 5200X, 5233MMX, 6180, 6200, 6233MMX, 6233X, 6266MMX, 6300MMX, 6333
Deskpro 2000 5166MMX, 5200MMX, 5233MMX, 6233MMX, 6266MMX, 6300MMX

Once unzipped you can boot the disks to re-create or update your software bios.

This will create a non-dos partition of approximately 3 meg.

DOWNLOAD DISK 1

DOWNLOAD DISK 2

DOWNLOAD DISK 3

Remember to create a folder called F10vp on your hard drive and extract all 3 files to it. Then run makedisk.bat to create the setup disks.

Karl's Forums!

Copyright © 2001-2005 © Copyright Karl Davis.

No part of this site may be reproduced in any format.All documents author acknowledged are copyright retained by the author.

Dead links or Errors ? Please email the Webmaster

Back to top

Karl's Forums
 

PC Help
Internet & Telecoms
PC Chat

Virus help and InfoSec

General Chat
Photo Corner
Test Forum

Feedback and Announcements
PC Help Archives